How to Set Up and Refill the Lost Mary BM6000

It lasts ten times longer than a standard pod kit and brings Lost Mary’s hugely popular e-liquid flavours to a hassle-free device. We explain how to set up, refill, and get the best performance from your Lost Mary BM6000 Prefilled Pod Kit. 

The Lost Mary BM6000 is one of the most popular "Big Puff" kits on the market. It combines compact design with a massive 6000-puff lifespan and a rechargeable battery. 

However, because the Lost Mary BM6000 Prefilled Pods use a unique 10ml "auto-refill" system to stay TPD compliant, the setup is a little different from a standard vape bar. 

If you're unsure how to assemble it or how to get the liquid into the pod, this guide will walk you through the process step-by-step. 

Key Takeaways

• It's TPD Compliant: The unique design allows for a legal 10ml capacity by keeping the e-liquid in a separate container. 
• Tip to Refill: You must turn the device upside down to let gravity feed the e-liquid from the bottle into the 2ml pod. 
• Rechargeable: Features a rechargeable battery and a display screen, ensuring you can use all the e-liquid. 
• Wait to Vape: Always wait a few minutes after setting up to allow the coil to saturate. 

How the BM6000 Works 

Before you start, it helps to understand the design. The device consists of three main parts: 

• The Body: Containing the battery and screen. 
• The 2ml Pod: This is built into the device and contains the coil. 
• The 10ml Refill Container: This clips into the side and acts as a reservoir.

Because UK law limits a vape tank to 2ml, the BM6000 gets around this by having a small 2ml tank that is constantly "refilled" by the larger 10ml bottle. 

Step-by-Step Setup Guide

Get your Lost Mary BM6000 ready for use with these easy steps: 

1. Unbox and Prep:
Remove the device and the separate e-liquid refill bottle from the packaging. You will see safety stickers on the device and the pod components—remove all of these. 

2. Prepare the Refill Bottle:
Take the lid off the 10ml refill bottle. Important: Do not remove the rubber cover or seal inside the bottle neck; this is part of the leak-proof mechanism. 

3. Prepare the Device:
Locate the rubber plug where the refill container is designed to slot into the pod (usually on the side). Pull this plug out to open the connection. 

4. Connect the Bottle:
Slide the 10ml refill bottle upwards and into the side of the device. Push it firmly until it clicks and sits flush with the body of the vape. It should feel secure. 

5. The "Tip-to-Fill" (Crucial Step):
This is the part new users often miss. Once the bottle is connected, turn the entire device upside down.

Hold it there for a few seconds. You are using gravity to let the e-liquid flow from the 10ml bottle into the 2ml pod chamber. You may see bubbles rising as the tank fills. 

6. Wait to Vape:
Once the 2ml pod is full, turn the device upright. Leave it to stand for 5-10 minutes. This allows the e-liquid to fully soak into the QUAQ mesh coil. If you vape immediately, you will burn the dry coil and ruin the device. 

7. Vape and Refill:
You are now ready to vape! When you notice the e-liquid level in the 2ml pod getting low (you can see this through the transparent window), simply turn the device upside down again to top it up from the main reservoir. 

How to Remove the Bottle (Disposal)

When the device is finally empty (after approx. 6000 puffs), you can disassemble it for responsible recycling. 

• Press the release catch located at the base of the battery. 
• Slide out the empty 10ml E-liquid Refill Container. 
• Slide out the Pod section.

You can then dispose of the battery at a WEEE recycling point, or participating vaping retail outlet, and the plastic components in your general waste.